2001 Subaru Outback Ac Relay Diagram

Solved at last.

Sorry for the long delay. This has been an adventure. As I have previously posted I had eliminated almost all the AC system except for the evaporator sensor. When I finally got some time and no rain I removed the glove box and cabin air filter and the plastic cover under the glove box.

By looking up under the dash I was able to see a connector that I was pretty sure was the connector going to the sensor. When I unplugged it the AC would not come on at all. Unfortunately this sensor has two wires coming from the evaporator area that go into a small black box that has a three wire connector on the other end. The factory service manual says nothing about how to test the three terminal sensor.

I was able to find another sensor online from a Subaru dealer for about $33 plus shipping which came to about $40 all together. When I just temporarily connected it to the AC circuit my erratic clutch problem was gone. So that pretty well confirmed that the old sensor was bad. The bad news was that now on warm humid mornings the evaporator was freezing over because the sensor was only hanging under the dash and not in the evaporator. I could tell it was freezing over because the airflow would become greatly diminished.

So how could I get the sensor where it needed to be without tearing half the car apart? As a previous poster noted you have to remove the blower and then the freon lines going to the evaporator and then pull the evaporator. What you have to do first is get a lot of other stuff out of the way before you can even remove the blower motor and housing.

The factory service manual was a big help as it led me step by step as I removed the center console, all the trim around the shift lever, the lower instrument panel and the center trim panel with the AC controls and then finally the blower motor and housing.

After I got the blower motor and housing out of the way I looked for a way to get to the evaporator. I finally realized I could reach in through the now open air duct to the front side of the evaporator. I took the new sensor and with it near the bottom and about in the center of the evaporator I carefully started wiggling it from side to side and up and down. As I felt it start to slip between the fins of the evaporator I carefully continued to push it between the fins while wiggling it a little. This now meant the sensor was back between the fins where it should be but just coming in from the front instead of the back. I just left the old sensor in place.

With the wire from the sensor now coming through the air duct I just pulled it to one side so when I put the blower motor and housing back in place the wire would be held in place by the foam padding where the blower motor housing and duct work connect together.

My wife spent the afternoon running errands on a very hot day here in central Georgia and she was very happy the AC worked fine all afternoon.

I have attached some pictures to help you understand what I have written. The first picture shows in the red the opening going into the air duct. I outlined it as it is a little hard to see with all the wiring hanging in the way. You can also see an arrow pointing to the wire going to the sensor.

The second picture shows the blower motor and housing now back in place. If you look closely you can see the gray wires of the sensor going behind the big wiring connector and then into the air duct. The last picture shows a closeup of the small black box with the twin gray wires going to the left and then down and into the air duct. The three wires on the other side of the connector go back into the AC wiring of the car. This is where you would find the sensor connector if you look up under the dash from below where the glove box would normally be. The connector is mounted on a plastic tab there.

I hope this will help anyone else that is having AC problems that seem to be intermittent. To get to the connector and disconnect it is actually pretty easy. From drawings I have the sensor for the Auto AC circuit is only two wire and can be checked easily with an ohmmeter. But as far as I know now the only way to check the three wire sensor is by substitution.

Carroll

Source: https://www.subaruforester.org/threads/2011-ac-intermittent-solved.782117/

Posted by: harrysualindesz.blogspot.com

Posting Komentar

0 Komentar